**52" Curved LED Light Bar with Upper Roof Mounting Brackets & 42" LED Curved Light Bar with Hidden Bumper Grille Mount Bracket Kit - Compatible with 2010-2019 Dodge Ram 2500 3500 - Includes 2x Wiring Harness - Perfect for Off-Roading, Night Driving & Truck Customization**

This bracket fits but it wont install 1 inch-3 inches above windshield without it nit being flush. It install almost perfectly ON TOP of the roof, but not where it is supposed to go, just above windshield.Harbor requires you to drill a hole through the roof of your vehicle poor design conceptI like these mounts but as other users have said, they don't fit a 52" light bar. I took one star off because I had to bend them to fit.first I mounted the brackets to my truck. I used self tapping screws instead of the included nutserts. that's when i discovered that the lightbar was about 2 inches short on either side. these mounts are sturdy and you're not going to bend them by hand. my solution was to wrap a ratcheting tie down around them and crank it until I could comfortably install the light bar.I'm still very happy with the outcome and the price. I recommend them as long as you understand that installing these will not be straightforward.Well they are easy to install once you figure out where they go, I was expecting them to mount inside the door frame like the others I have installed, NO these are literally roof mounts, right in the body seam, No directions came with them so I spent some time trying to figure it out. Also I would suggest notching the center of the driver side out to accommodate for wiring to pass through, I don’t like for those to show and when bolted down you will definitely smash your wires so I notched the center out to bring the light wires down under it to keep them hidden, add some paint and or clear coat to prevent rusting. Overall good productSo I received the first one and it did not fit the contour of my door jam no matter what angle I did and I’ve installed these on other trucks I’ve owned before. I had another one sent to me for replacement which came so fast that I haven’t even had a chance to get the first one to the UPS store to send back. The new one is the same way so I was very confused and went back on here to make sure I ordered the right one. And I did. My truck is a 2013 Ram 2500 so this should be working and I was at a loss so I went down the road to a garage that does custom work on vehicles who have had tons of experience with this stuff and they said there is no way this is for my truck so I don’t understand. I come home and walk over to my tools and grab my 52” curve light and go to put it back in the box and walked it back to the shed to put it away for the moment. I turned around and tripped and fell on it. Now I have a broken $150 light that should have not even had to go back into hiding in fact it should be on my truck right now. All together this was a bad experience over some brackets that say they are for my truck but don’t fit. Now I have a broken light and 2 sets of brackets I can’t use. I’m definitely not happy. I spend thousands of dollars here on Amazon and rarely do I have issues but man when I do boy do I.I would recommend getting a rivnut tool the bolt the is supplied is junk but outher than that it is a good kit for the money and the brackets are 1/8 steel so you don’t have to worry about it bending if a branch hits itI am over all very happy with these brackets. They are going to be as hard to install as any other bracket. I am happy they used rivnuts vs rivets. In my opinion they are a lot stronger and easier to work with given you have the correct tool. They did bend a little to mount to the lightbar but that could just be because of my Cali Raised LED Lightbar. I would recommend this to anyone using a 52" lightbar on a Dodge Ram.Don't buy these unless you really want to f****** up your truck terrible design . Forget about instructions. Literally just tells you where to place it. Drill a hole and install would never buy againFits almost perfect, instructions say to mount 1 inch from top of windshield, I went a little more (1.75) and fits like a glove. I would not use rivet nuts included, go and buy yourself some self tapping screws. Came with minor paint ship on mount but doesn’t look horrible. Other wise, would buy again if needed a cheap way out.